ENUM IEEE80211_HW_FL(9) The basic mac80211 driver inte ENUM IEEE80211_HW_FL(9)

NAME enum_ieee80211_hw_flags - hardware flags


CONSTANTS IEEE80211_HW_HAS_RATE_CONTROL The hardware or firmware includes rate control, and cannot be controlled by the stack. As such, no rate control algorithm should be instantiated, and the TX rate reported to userspace will be taken from the TX status instead of the rate control algorithm. Note that this requires that the driver implement a number of callbacks so it has the correct information, it needs to have the set_rts_threshold callback and must look at the BSS config use_cts_prot for G/N protection, use_short_slot for slot timing in 2.4 GHz and use_short_preamble for preambles for CCK frames.

IEEE80211_HW_RX_INCLUDES_FCS Indicates that received frames passed to the stack include the FCS at the end.

IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING Some wireless LAN chipsets buffer broadcast/multicast frames for power saving stations in the hardware/firmware and others rely on the host system for such buffering. This option is used to configure the IEEE 802.11 upper layer to buffer broadcast and multicast frames when there are power saving stations so that the driver can fetch them with ieee80211_get_buffered_bc.

IEEE80211_HW_SIGNAL_UNSPEC Hardware can provide signal values but we don´t know its units. We expect values between 0 and max_signal. If possible please provide dB or dBm instead.

IEEE80211_HW_SIGNAL_DBM Hardware gives signal values in dBm, decibel difference from one milliwatt. This is the preferred method since it is standardized between different devices. max_signal does not need to be set.

IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC This device needs to get data from beacon before association (i.e. dtim_period).

IEEE80211_HW_SPECTRUM_MGMT Hardware supports spectrum management defined in 802.11h Measurement, Channel Switch, Quieting, TPC

IEEE80211_HW_AMPDU_AGGREGATION Hardware supports 11n A-MPDU aggregation.

IEEE80211_HW_SUPPORTS_PS Hardware has power save support (i.e. can go to sleep).

IEEE80211_HW_PS_NULLFUNC_STACK Hardware requires nullfunc frame handling in stack, implies stack support for dynamic PS.

IEEE80211_HW_SUPPORTS_DYNAMIC_PS Hardware has support for dynamic PS.

IEEE80211_HW_MFP_CAPABLE Hardware supports management frame protection (MFP, IEEE 802.11w).

IEEE80211_HW_WANT_MONITOR_VIF The driver would like to be informed of a virtual monitor interface when monitor interfaces are the only active interfaces.

IEEE80211_HW_NO_AUTO_VIF The driver would like for no wlanX to be created. It is expected user-space will create vifs as desired (and thus have them named as desired).

IEEE80211_HW_SW_CRYPTO_CONTROL The driver wants to control which of the crypto algorithms can be done in software - so don´t automatically try to fall back to it if hardware crypto fails, but do so only if the driver returns 1. This also forces the driver to advertise its supported cipher suites.

IEEE80211_HW_SUPPORT_FAST_XMIT The driver/hardware supports fast-xmit, this currently requires only the ability to calculate the duration for frames.

IEEE80211_HW_REPORTS_TX_ACK_STATUS Hardware can provide ack status reports of Tx frames to the stack.

IEEE80211_HW_CONNECTION_MONITOR The hardware performs its own connection monitoring, including periodic keep-alives to the AP and probing the AP on beacon loss.

IEEE80211_HW_QUEUE_CONTROL The driver wants to control per-interface queue mapping in order to use different queues (not just one per AC) for different virtual interfaces. See the doc section on HW queue control for more details.

IEEE80211_HW_SUPPORTS_PER_STA_GTK The device´s crypto engine supports per-station GTKs as used by IBSS RSN or during fast transition. If the device doesn´t support per-station GTKs, but can be asked not to decrypt group addressed frames, then IBSS RSN support is still possible but software crypto will be used. Advertise the wiphy flag only in that case.

IEEE80211_HW_AP_LINK_PS When operating in AP mode the device autonomously manages the PS status of connected stations. When this flag is set mac80211 will not trigger PS mode for connected stations based on the PM bit of incoming frames. Use ieee80211_start_ps/ieee8021_end_ps to manually configure the PS mode of connected stations.

IEEE80211_HW_TX_AMPDU_SETUP_IN_HW The device handles TX A-MPDU session setup strictly in HW. mac80211 should not attempt to do this in software.

IEEE80211_HW_SUPPORTS_RC_TABLE The driver supports using a rate selection table provided by the rate control algorithm.

IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF Use the P2P Device address for any P2P Interface. This will be honoured even if more than one interface is supported.

IEEE80211_HW_TIMING_BEACON_ONLY Use sync timing from beacon frames only, to allow getting TBTT of a DTIM beacon.

IEEE80211_HW_SUPPORTS_HT_CCK_RATES Hardware supports mixing HT/CCK rates and can cope with CCK rates in an aggregation session (e.g. by not using aggregation for such frames.)

IEEE80211_HW_CHANCTX_STA_CSA Support 802.11h based channel-switch (CSA) for a single active channel while using channel contexts. When support is not enabled the default action is to disconnect when getting the CSA frame.

IEEE80211_HW_SUPPORTS_CLONED_SKBS The driver will never modify the payload or tailroom of TX skbs without copying them first.

IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS The HW supports scanning on all bands in one command, mac80211 doesn´t have to run separate scans per band.

IEEE80211_HW_TDLS_WIDER_BW The device/driver supports wider bandwidth than then BSS bandwidth for a TDLS link on the base channel.

NUM_IEEE80211_HW_FLAGS number of hardware flags, used for sizing arrays

DESCRIPTION These flags are used to indicate hardware capabilities to the stack. Generally, flags here should have their meaning done in a way that the simplest hardware doesn´t need setting any particular flags. There are some exceptions to this rule, however, so you are advised to review these flags carefully.

AUTHOR Johannes Berg <johannes@sipsolutions.net> Author.

COPYRIGHT Kernel Hackers Manual 2.6. April 2016 ENUM IEEE80211_HW_FL(9)